a)      Wall mounted box for miniature  circuit breakers

b)      Integrated 35mm DIN rail (standard  profile rail)

c)       Ingress protection rating minimum  IP30

d)      Fully isolated

e)      Enough space for minimum 2 units  of miniature circuit breaker, minimum 35 or 36mm in total width

f)       2 pieces integrated or separately  supplied junction terminals for neutral and earth conductors;

g)      connection of each up to 6  conductors 1.5 and 2.5 mm² solid copper and one conductor 16mm² solid  aluminum or copper conductor,

h)      not more than 2 conductors of same  cross section per one screw terminal

i)         Suitably prepared entries or knock-outs for standard cable sizes from  all four sides

j)         Including all screws

k)      Packaging: It is preferred that  the distribution box including the above specified accessories is packed as  an individual set. Alternatively the individual members of the set are  allowed to be supplied in bulk but only in quantities of no more than 500 pieces  in one box.

* l0 V- d5 I7 H# v; X6 X

a)      Cover strip for miniature circuit  breaker not installed in the surface mounted distribution box;

b)      if the distribution box offered is  specified for 2 miniature circuit breakers (MCB), a cover strip is needed for  1 MCB;

c)       if the distribution box can  accommodate 4 MCBs, cover strips for 3 MCBs must be supplied

d)      Picture for illustration shows  cover strip for 12 units, the number of units needed depends on the size of  the box

e)       Easy to separate on site

1 t" e- ^4 }6 `2 {" n* S

a)      Minimum height 20mm

b)      Self-adhesive

c)       Long lasting quality

/ f9 h( l  [* C. I( H7 I  e

a)      For DIN rail (standard profile  rail) installation

b)      Size suitable to be installed in  the surface mounted distribution box, leaving space to install a second  miniature circuit breaker for later extensions

c)       Rated current 6A, curve “B”

d)      Single pole

e)      Incoming conductor cross section  up to 16mm² aluminum

f)        Outgoing conductor cross section  up to 16mm²

- Z% G$ P& n% ^1 M% r

g)      For DIN rail (standard profile  rail) installation

h)      Size suitable to be installed in  the surface mounted distribution box, leaving space to install a second  miniature circuit breaker for later extensions

i)         Rated current 16A, curve “B”

j)         Single pole

k)      Incoming conductor cross section  up to 16mm² aluminum

l)         Outgoing conductor cross section  up to 16mm²

5 I: r" p3 i, {  ^

a)       1 Gang

b)       250V, 10A, AC

c)        Clamping connection capacity 2.5mm²

d)       Robust and high quanlity

e)       Bright white color

f)        According to BS standard

a)       3 Gang

b)       250V, 10A, AC

c)        Clamping connection capacity 2.5mm²

d)       Robust and high quanlity

e)       Bright white color

f)        According to BS standard

a)       For light switches

b)       Surface mounted box

c)        Fully compatible with light switch

d)      Incl. all  screws needed to install the switch

e)      Knock-outs  for the cable on minimum top and bottom side

f)       Bright  white color, identical to switch

g)       According to BS standard

a)      2 Gang Double pole switched socket  outlet

b)      13A

c)       Including surface mounted box

d)      Bright white color

e)      Robust and high quality

f)       According to BS standard

a)      LED lamp

b)      Minimum 6W, maximum 9W

c)       Minimum light current 600 lm

d)      Light temperature 4000K, neutral  white

e)      Edison E27 screw base

f)       Average rated life 20000 hours

g)      Switching cycles 15000

h)      Non-flickering

i)         Instant 100% light

j)         Angle of radiation >= 200°

k)      Supply full data sheet or  catalogue with high-quality pictures, dimensions and full technical  specification

/ j3 [" Y5 U9 O# m

a)      For wall and roof mounting

b)      Edison E27 screw base

c)       Fully suitable for the LED lamp  supplied and other standard lamps

d)       Supply full data sheet or  catalogue with high-quality pictures, dimensions and full technical  specification

) A! u1 n+ h' [" J8 o' K) ~+ h

a)      2x 1.5mm² massive copper conductor

b)      70°C conductor temperature

c)       PVC insulation and sheath

d)      Voltage rating 300/500V

e)      British standard

f)       Provide full technical data sheet

g)       Packaging - Coils of minimum  100m, maximum 500m

+ l; y/ _5 z2 m7 I8 M

a)      2x 2.5mm² massive copper conductor

b)      70°C conductor temperature

c)       PVC insulation and sheath

d)      Voltage rating 300/500V

e)      British standard

f)       Provide full technical data sheet

g)      Packaging -Coils of minimum 100m,  maximum 500m

' O% J5 C! _1 R

a)      Preferably 20mm or 25mm in  diameter

b)      Copper-plated steel

c)       Length 1m … 1.2m

d)       Including screw terminal for  copper cable

4 q; L6 x5 R( y  d

a)      Single core copper cable

b)      4mm² rigid conductor

c)       Yellow-green or black PVC sheath

d)       Packaging - In coils of 100 m

% b% J4 R6 H- G/ p

a)      Cable clip suitable for both twin  and earth cable diameters

b)       Including hardened steel nail of  30 or 35mm length

  q# R, ]) Q1 m4 X5 ~2 d

a)      4x35mm

b)      Galvanized  steel

c)       Fully suitable  for wall plug

a)      6mm diameter

b)      30mm length

c)       PVC

2 Y" j3 Y5 b3 t+ P$ K' b- o

a)      Ingress protection rating IP 54

b)      Approximate size 80 x 80 x  35 mm³

c)       2 or 3 self-sealing cut cable  inlets for cables up to 3 x 2.5mm² on each side

d)       Exterior mounting flaps with  transverse and oblong holes ensure subsequent alignment

! ^5 a, v4 [5 r8 f8 ^

a)      Screw or push wire connector for  up to 5 massive copper conductors 1.5 or 2.5 mm²

b)      For 300V AC

c)        Packaging - Supply in bulk  allowed, screw connectors, 12 connectors in one bar

4 E& p7 n- ?; P0 ^. M% D

a)      6 kg dry powder

b)      With bracket for wall mounting

c)        Specification according BS EN 3

  G) Y7 W2 j6 P1 C3 L9 Z" U( Z3 s

a)      Optical/photoelectric smoke  detection

b)      Loud alarm signal, 85 dBA at  10 feet

c)       Test botton

d)      Optical and acoustic signal for  low battery

e)      Battery lifetime minimum 2 years

f)       Including first set of batteries

g)      Including screws for wall mounting

& P) m6 U4 F; Z; u' W' ~